Polymer fluidity influenced by the percentage of filler

Staněk, Michal; Maňas, David; Maňas, Miroslav; Kyas, Kamil; Šenkeřík, Vojtěch; Škrobák, Adam; Navrátil, Jan

dc.title	Polymer fluidity influenced by the percentage of filler	en
dc.contributor.author	Staněk, Michal
dc.contributor.author	Maňas, David
dc.contributor.author	Maňas, Miroslav
dc.contributor.author	Kyas, Kamil
dc.contributor.author	Šenkeřík, Vojtěch
dc.contributor.author	Škrobák, Adam
dc.contributor.author	Navrátil, Jan
dc.relation.ispartof	International Journal of Mathematics and Computers in Simulation
dc.identifier.issn	1998-0159 Scopus Sources, Sherpa/RoMEO, JCR
dc.date.issued	2012
utb.relation.volume	6
utb.relation.issue	6
dc.citation.spage	542
dc.citation.epage	549
dc.type	article
dc.language.iso	en
dc.publisher	North Atlantic University Union (NAUN)	en
dc.relation.uri	http://www.naun.org/multimedia/NAUN/mcs/16-590.pdf
dc.subject	Fluidity	en
dc.subject	Injection molding	en
dc.subject	Mold	en
dc.subject	Polymer	en
dc.subject	Roughness	en
dc.subject	Surface	en
dc.description.abstract	Delivery of polymer melts into the mold cavity is the most important stage of the injection molding process. This paper shows the influence of cavity surface roughness and technological parameters on the flow length of polymers into mold cavity. Application of the measurement results may have significant influence on the production of shaping parts of the injection molds especially in changing the so far used processes and substituting them by less costly production processes which might increase the competitiveness of the tool producers and shorten the time between product plan and its implementation.	en
utb.faculty	Faculty of Technology
utb.faculty	Faculty of Applied Informatics
dc.identifier.uri	http://hdl.handle.net/10563/1003200
utb.identifier.rivid	RIV/70883521:28110/12:43869127!RIV13-MSM-28110___
utb.identifier.rivid	RIV/70883521:28140/12:43869127!RIV13-MSM-28140___
utb.identifier.obdid	43869358
utb.identifier.scopus	2-s2.0-84875717801
utb.source	j-scopus
dc.date.accessioned	2013-04-29T12:17:51Z
dc.date.available	2013-04-29T12:17:51Z
utb.contributor.internalauthor	Staněk, Michal
utb.contributor.internalauthor	Maňas, David
utb.contributor.internalauthor	Maňas, Miroslav
utb.contributor.internalauthor	Kyas, Kamil
utb.contributor.internalauthor	Šenkeřík, Vojtěch
utb.contributor.internalauthor	Škrobák, Adam
utb.contributor.internalauthor	Navrátil, Jan
utb.fulltext.affiliation	M. Stanek, D. Manas, M. Manas, K. Kyas, V. Senkerik, A. Skrobak and J. Navratil Michal Stanek is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (phone: +420576035153; fax: +420576035176; e-mail: [email protected]). David Manas is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: [email protected]). Miroslav Manas is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: [email protected]). Kamil Kyas is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: [email protected]). Vojtech Senkerik is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: [email protected]). Adam Skrobak is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: [email protected]). Jan Navratil is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: [email protected]).
utb.fulltext.dates	-
utb.fulltext.sponsorship	This paper is supported by the internal grant of TBU in Zlin No. IGA/FT/2012/041 funded from the resources of specific university research and by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089.
utb.fulltext.faculty	-
utb.fulltext.ou	-