System for automatic inspection of bandsaw blades

Sysala, Tomáš; Stuchlík, Karel; Neumann, Petr

dc.title	System for automatic inspection of bandsaw blades	en
dc.contributor.author	Sysala, Tomáš
dc.contributor.author	Stuchlík, Karel
dc.contributor.author	Neumann, Petr
dc.relation.ispartof	WSEAS Transactions on Environment and Development
dc.identifier.issn	1790-5079 Scopus Sources, Sherpa/RoMEO, JCR
dc.date.issued	2019
utb.relation.volume	15
dc.citation.spage	500
dc.citation.epage	509
dc.type	article
dc.language.iso	en
dc.publisher	World Scientific and Engineering Academy and Society
dc.relation.uri	http://www.wseas.org/multimedia/journals/environment/2019/b065115-069.pdf
dc.subject	automatic inspection	en
dc.subject	bandsaw	en
dc.subject	HMI	en
dc.subject	Programmable Logic Controler	en
dc.subject	SCADA	en
dc.subject	Simatic	en
dc.description.abstract	The article deals with a new inspection method for the bandsaw blade eligibility checking. For better understanding, the individual bandsaw blade areas are described together with relevant parameters overview. The method design description follows. The current method drawback are discussed, and there are stressed the advantages of our innovative automatic inspection method. We present arrangement of our design in individual blocks together with the application software functions. The article also presents both the design model and the realised prototype measurement results. The constructed device based on our design minimizes the human error influence. © 2019, World Scientific and Engineering Academy and Society. All rights reserved.	en
utb.faculty	Faculty of Applied Informatics
dc.identifier.uri	http://hdl.handle.net/10563/1009608
utb.identifier.obdid	43881112
utb.identifier.scopus	2-s2.0-85079639910
utb.source	j-scopus
dc.date.accessioned	2020-03-12T14:04:41Z
dc.date.available	2020-03-12T14:04:41Z
dc.rights	Attribution 4.0 International
dc.rights.uri	https://creativecommons.org/licenses/by/4.0/
dc.rights.access	openAccess
utb.ou	Department of Automation and Control Engineering
utb.ou	Department of Electronics and Measurements
utb.ou	CEBIA-Tech
utb.contributor.internalauthor	Sysala, Tomáš
utb.contributor.internalauthor	Stuchlík, Karel
utb.contributor.internalauthor	Neumann, Petr
utb.fulltext.affiliation	TOMAS SYSALA 1, KAREL STUCHLIK 1, PETR NEUMANN 2 1 Department of Automation and Control Engineering 2 Department of Electronics and Measurements Tomas Bata University in Zlin, Faculty of Applied Informatics Nad Stranemi 4511, 760 05 Zlin CZECH REPUBLIC [email protected] https://fai.utb.cz/
utb.fulltext.dates	-
utb.fulltext.sponsorship	This work was supported by the Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Programme project No. LO1303 (MSMT-7778/2014) and by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089.
utb.scopus.affiliation	Department of Automation and Control Engineering, Tomas Bata University in Zlin, Faculty of Applied Informatics, Nad Stranemi 4511, Zlin, 760 05, Czech Republic; Department of Electronics and Measurements, Tomas Bata University in Zlin, Faculty of Applied Informatics, Nad Stranemi 4511, Zlin, 760 05, Czech Republic
utb.fulltext.projects	LO1303
utb.fulltext.projects	MSMT-7778/2014
utb.fulltext.projects	CZ.1.05/2.1.00/03.0089
utb.fulltext.faculty	Faculty of Applied Informatics
utb.fulltext.faculty	Faculty of Applied Informatics
utb.fulltext.faculty	Faculty of Applied Informatics
utb.fulltext.ou	Department of Automation and Control Engineering
utb.fulltext.ou	Department of Automation and Control Engineering
utb.fulltext.ou	Department of Electronics and Measurements