Mechanical properties of injection molded and compression molded samples from nature-butadiene rubber

Škrobák, Adam; Janoštík, Václav; Staněk, Michal; Maňas, David; Ovsík, Martin; Šenkeřík, Vojtěch; Řezníček, Martin

dc.title	Mechanical properties of injection molded and compression molded samples from nature-butadiene rubber	en
dc.contributor.author	Škrobák, Adam
dc.contributor.author	Janoštík, Václav
dc.contributor.author	Staněk, Michal
dc.contributor.author	Maňas, David
dc.contributor.author	Ovsík, Martin
dc.contributor.author	Šenkeřík, Vojtěch
dc.contributor.author	Řezníček, Martin
dc.relation.ispartof	MATEC Web of Conferences 20th International Conference on Circuits, Systems, Communications and Computers (CSCC 2016)
dc.identifier.issn	2261-236X Scopus Sources, Sherpa/RoMEO, JCR
dc.date.issued	2016
utb.relation.volume	76
dc.event.title	20th International Conference on Circuits, Systems, Communications and Computers (CSCC)
dc.event.location	Corfu
utb.event.state-en	Greece
utb.event.state-cs	Řecko
dc.event.sdate	2016-07-14
dc.event.edate	2016-07-17
dc.type	conferenceObject
dc.language.iso	en
dc.publisher	EDP Sciences
dc.identifier.doi	10.1051/matecconf/20167602023
dc.relation.uri	https://www.matec-conferences.org/articles/matecconf/abs/2016/39/matecconf_cscc2016_02023/matecconf_cscc2016_02023.html
dc.description.abstract	The aim of this paper is to show what extent there is an impact on the mechanical properties (tensile strength and tear strength) of a standardized testing sample made of rubber compound based on nature rubber and butadiene rubber produced by injection molding in comparison with a sample produced by classic preparation (cutting out a compression molded plate) according to the standard ISO 23529. For realization of this study it was necessary to design and produce an injection mold for all types testing samples. Subsequently, mechanical properties such as the tensile stress-strain and tear strenght of compression molded samples and injection molded samples were studied, compared and discussed.	en
utb.faculty	Faculty of Applied Informatics
dc.identifier.uri	http://hdl.handle.net/10563/1007013
utb.identifier.obdid	43875899
utb.identifier.scopus	2-s2.0-85016116734
utb.identifier.wok	000392332200036
utb.source	d-wok
dc.date.accessioned	2017-07-25T08:54:45Z
dc.date.available	2017-07-25T08:54:45Z
dc.description.sponsorship	TBU in Zlin [IGA/FT/2016/010]; Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Programme [LO1303 (MSMT-7778/2014)]; European Regional Development Fund under the project CEBIA-Tech [CZ.1.05/2.1.00/03.0089]
dc.rights	Attribution 4.0 International
dc.rights.uri	https://creativecommons.org/licenses/by/4.0/
dc.rights.access	openAccess
utb.contributor.internalauthor	Škrobák, Adam
utb.contributor.internalauthor	Janoštík, Václav
utb.contributor.internalauthor	Staněk, Michal
utb.contributor.internalauthor	Maňas, David
utb.contributor.internalauthor	Ovsík, Martin
utb.contributor.internalauthor	Šenkeřík, Vojtěch
utb.contributor.internalauthor	Řezníček, Martin
utb.fulltext.affiliation	Adam Skrobak 1,Václav Janoštík 1, Michal Stanek 1, David Manas 1, Martin Ovsik 1, Vojtech Senkerik 1 and Martin Reznicek 1 1 Tomas Bata University in Zlin, TGM 5555, 760 01 Zlin, Czech Republic a Corresponding author: [email protected]
utb.fulltext.dates	-
utb.fulltext.sponsorship	This paper is supported by the internal grant of TBU in Zlin No. IGA/FT/2016/010 funded from the resources of specific university research and by the Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Programme project No. LO1303 (MSMT-7778/2014) and also by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089.
utb.fulltext.projects	IGA/FT/2016/010
utb.fulltext.projects	LO1303 (MSMT-7778/2014)
utb.fulltext.projects	CZ.1.05/2.1.00/03.0089