Micro-hardness of surface layer of irradiated Polybutene Terephthalate (PBT)

Maňas, David; Maňas, Miroslav; Ovsík, Martin; Staněk, Michal; Chvátalová, Lenka; Stoklásek, Pavel; Hýlová, Lenka

dc.title	Micro-hardness of surface layer of irradiated Polybutene Terephthalate (PBT)	en
dc.contributor.author	Maňas, David
dc.contributor.author	Maňas, Miroslav
dc.contributor.author	Ovsík, Martin
dc.contributor.author	Staněk, Michal
dc.contributor.author	Chvátalová, Lenka
dc.contributor.author	Stoklásek, Pavel
dc.contributor.author	Hýlová, Lenka
dc.relation.ispartof	MATEC Web of Conferences 20th International Conference on Circuits, Systems, Communications and Computers (CSCC 2016)
dc.identifier.issn	2261-236X Scopus Sources, Sherpa/RoMEO, JCR
dc.date.issued	2016
utb.relation.volume	76
dc.event.title	20th International Conference on Circuits, Systems, Communications and Computers (CSCC)
dc.event.location	Corfu
utb.event.state-en	Greece
utb.event.state-cs	Řecko
dc.event.sdate	2016-07-14
dc.event.edate	2016-07-17
dc.type	conferenceObject
dc.language.iso	en
dc.publisher	EDP Sciences
dc.identifier.doi	10.1051/matecconf/20167602018
dc.relation.uri	https://www.matec-conferences.org/articles/matecconf/abs/2016/39/matecconf_cscc2016_02018/matecconf_cscc2016_02018.html
dc.description.abstract	Using high doses of beta radiation for polybutylene terephthalate (PBT) and its influence on the changes of micromechanical properties of surface layer has not been studied in detail so far. The specimens of PBT were made by injection moulding technology and irradiated by high doses of beta radiation (0, 132, 165 and 198 kGy). The changes in the microstructure and micromechanical properties of surface layer were evaluated using WAXS and instrumented microhardness test. The results of the measurements showed considerable increase in micromechanical properties (indentation hardness, indentation elastic modulus) when high doses of beta radiation are used.	en
utb.faculty	University Institute
dc.identifier.uri	http://hdl.handle.net/10563/1006996
utb.identifier.obdid	43875893
utb.identifier.scopus	2-s2.0-85016109250
utb.identifier.wok	000392332200031
utb.source	d-wok
dc.date.accessioned	2017-07-13T14:50:31Z
dc.date.available	2017-07-13T14:50:31Z
dc.description.sponsorship	Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Programme [LO1303 (MSMT-7778/2014)]; European Regional Development Fund under the project CEBIA-Tech [CZ.1.05/2.1.00/03.0089]; internal grant of TBU in Zlin [IGA/FT/2016/010]; Ministry of Education, Youth and Sports of the Czech Republic
dc.rights	Attribution 4.0 International
dc.rights.uri	https://creativecommons.org/licenses/by/4.0/
dc.rights.access	openAccess
utb.contributor.internalauthor	Maňas, David
utb.contributor.internalauthor	Maňas, Miroslav
utb.contributor.internalauthor	Ovsík, Martin
utb.contributor.internalauthor	Staněk, Michal
utb.contributor.internalauthor	Chvátalová, Lenka
utb.contributor.internalauthor	Stoklásek, Pavel
utb.contributor.internalauthor	Hýlová, Lenka
utb.fulltext.affiliation	David Manas 1,a, Miroslav Manas 1, Martin Ovsik 1, Michal Stanek 1, Lenka Chvatalova 1, Pavel Stoklasek 1 and Lenka Hylova 1 1 Tomas Bata University in Zlin, Nam. T.G.Masaryka 5555, Zlin, 760 01, Czech Republic a Corresponding author: [email protected]
utb.fulltext.dates	-
utb.fulltext.sponsorship	This work was supported by the Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Programme project No. LO1303 (MSMT-7778/2014) and also by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089 and the internal grant of TBU in Zlin No. IGA/FT/2016/010 funded from the resources of specific university research and by the Ministry of Education, Youth and Sports of the Czech Republic.